GB/T 22563-2008 萤石的水分测定

作者:标准资料网 时间:2024-05-20 08:06:18   浏览:9343   来源:标准资料网
下载地址: 点击此处下载
基本信息
标准名称:萤石的水分测定
英文名称:All grades of fluorspar - Determination of moisture content of a lot
中标分类: 矿业 >> 非金属矿 >> 冶金辅助原料矿
ICS分类: 采矿和矿产品 >> 非金属矿
发布部门:中华人民共和国国家质量监督检验检疫总局 中国国家标准化管理委员会
发布日期:2008-12-06
实施日期:2009-10-01
首发日期:2008-12-06
作废日期:
主管部门:中国钢铁工业协会
提出单位:中国钢铁工业协会
归口单位:全国钢标准化技术委员会
起草单位:武汉钢铁(集团)公司、冶金工业信息标准研究院
起草人:李小杰、沈克、高建平、仇金辉、杨红、贾丽晖、白汉芳
出版社:中国标准出版社
出版日期:2009-06-01
页数:8页
计划单号:20067336-T-605
适用范围

本标准规定了测定批量萤石水分平均值方法的范围、术语和定义、原理、设备、试样、测定步骤、结果计算和试验报告等内容。
本标准适用于萤石的所有的品级,即酸级、陶瓷级以及三个冶金级(精矿、球团矿和原矿)的水分测定。

前言

没有内容

目录

没有内容

引用标准

下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件,其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本标准,然而,鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件,其最新版本适用于本标准。
GB/T22564—2008 萤石取样和试样制备(ISO8875:1992,IDT)

所属分类: 矿业 非金属矿 冶金辅助原料矿 采矿和矿产品 非金属矿
下载地址: 点击此处下载
基本信息
标准名称:汽车产品编号规则
英文名称:Motor vehicles-type and model designation
中标分类: 车辆 >> 车辆综合 >> 基础标准与通用方法
ICS分类: 道路车辆工程 >> 道路车辆装置
替代情况:汽130-1959部分 GB 4991-1985部分 JB 2321-1978 GB 6420-1986部分 JT 3112-1985 CJ 6-1984
发布日期:1988-06-25
实施日期:1989-01-01
首发日期:1900-01-01
作废日期:1900-01-01
起草单位:中汽技术研究中心
出版日期:1900-01-01
页数:6页
适用范围

没有内容

前言

没有内容

目录

没有内容

引用标准

没有内容

所属分类: 车辆 车辆综合 基础标准与通用方法 道路车辆工程 道路车辆装置
Product Code:SAE J1979
Title:E/E Diagnostic Test Modes-Equivalent to Iso/Dis 15031:April 30,2002
Issuing Committee:Vehicle E E System Diagnostic Standards Committee
Scope:This SAE Recommended Practice defines diagnostic test modes, and request and response messages, necessary to be supported by vehicle manufacturers and test tools to meet the requirements of the California OBD II and Federal OBD regulations, which pertain to vehicle emission-related data only. These messages are intended to be used by any service tool capable of performing the mandated diagnostics. In addition, capabilities are defined that are intended to meet other Federal and State regulations pertaining to related issues such as Inspection and Maintenance (I/M) and service information availability. This document provides the mechanism to satisfy requirements included in regulations, and not all capabilities included in this document are required by regulations. This document also is not considered a final authority for interpretation of the regulations, so the reader should determine the applicability of the capabilities defined in this document for their specific need. diagnostic Test Modes included in this document are: a. Mode $01聴Request current Powertrain Diagnosstic Data; Analog inputs and outputs, digital inputs and outputs, System status information, Calculated values; b. Mode $02聴Request Powertrain Freeze Frame Data; Analog inputs and outputs, Digital inputs and outputs, System status information, Calculated values; c. Mode $03聴Request Emmission-Related Powertrain Diagnostic Trouble Codes; d. Mode $04聴Clear/Reset Emission-Related Diagnostic Information; e. Mode $05聴Request Oxygen Sensor Monitoring Test Results; f. Mode $06聴Request On-Board Monitoring Test Results for Non-Continuously Monitored Systems; g. Mode $07聴Request On-Board monitoring Test Results for Continuously Monitored Systems; h. Mode $08聴Request Control of On-Board System, Test, or Component; i. Mode $09聴Request Vehicle Information. For each test mode, this specification includes: a. Functional descriptions of test mode; b. Request and response message formats. For some of the more complex test modes, an example of messages and an explanation of the interpretation of those messages is included.